High power LED conductive silver paste and its packaging technology and trends

2012-05-19 00:00:00

Click:

**Preface**

Due to the complexity of its structure and manufacturing process, and because it directly affects the performance and service life of LEDs, high-power LED packaging has been a research hotspot in recent years. In particular, high-power white LED packaging is among the most intensively studied topics. The functions of LED packaging mainly include: 1. mechanical protection to improve reliability; 2. enhanced heat dissipation to lower the chip junction temperature and improve LED performance; 3. optical control to increase light extraction efficiency and optimize beam distribution; and 4. power management, including AC/DC conversion and power control.

The choice of LED packaging method, materials, structure, and process is mainly determined by factors such as chip structure, optoelectronic/mechanical characteristics, specific applications, and cost. Over more than 40 years of development, LED packaging has gone through several stages, including Lamp LEDs, SMD LEDs, and Power LEDs. As chip power increases, especially with the demands of solid‑state lighting technology, new and higher requirements are placed on the optical, thermal, electrical, and mechanical aspects of LED packaging. To effectively reduce the packaging thermal resistance and improve light extraction efficiency, completely new technical approaches must be adopted in packaging design.

**I. High‑Thermal‑Conductivity Conductive Adhesives and Conductive Silver Adhesives for High‑Power LEDs**

Conductive adhesives are indispensable materials in LED production and packaging. They are required to have good electrical and thermal conductivity, high shear strength, and strong adhesion.

**II. Key Technologies for High‑Power LED Packaging**

High‑power LED packaging mainly involves optics, thermal management, electrical characteristics, structural design, and processing technology. These factors are both independent and mutually influential. Among them, light output is the purpose of LED packaging, heat dissipation is the key, while electrical design, structure, and process are the means, and performance is the concrete manifestation of packaging level. In terms of process compatibility and cost reduction, LED packaging design should be carried out simultaneously with chip design; that is, the packaging structure and process should be considered during chip design. Otherwise, after chip fabrication is completed, it may be necessary to adjust the chip structure to meet packaging requirements, which prolongs the product development cycle, increases process costs, and may sometimes even be impossible.

Specifically, the key technologies for high‑power LED packaging include:

**(1) Low‑Thermal‑Resistance Packaging Technology**

With the current luminous efficacy of LEDs, about 80% of the input electrical energy is converted into heat, and because the LED chip area is small, chip heat dissipation is a critical issue that must be addressed in LED packaging. This mainly includes chip placement, selection of packaging materials (substrate materials and thermal interface materials), process optimization, and heat sink design.

The thermal resistance of LED packaging mainly includes the internal thermal resistance of materials (heat‑dissipating substrate and heat sink structure) and interfacial thermal resistance. The heat‑dissipating substrate absorbs the heat generated by the chip and conducts it to the heat sink for heat exchange with the environment. Commonly used substrate materials include silicon, metals (e.g., aluminum, copper), ceramics (e.g., Al₂O₃, AlN, SiC), and composite materials. For example, Nichia’s third‑generation LEDs use CuW as a substrate, with 1‑mm chips flip‑chip bonded onto the CuW substrate, reducing packaging thermal resistance and improving luminous power and efficiency. Lamina Ceramics has developed a low‑temperature co‑fired ceramic metal substrate and corresponding LED packaging technology, in which high‑power LED chips suitable for eutectic bonding are fabricated together with the ceramic substrate, and then the LED chip is directly soldered to the substrate. Because this substrate integrates a eutectic bonding layer, ESD protection circuits, driver circuits, and compensation control circuits, the structure is simple, and the high thermal conductivity of the materials and fewer thermal interfaces significantly improve heat dissipation performance, providing a solution for high‑power LED array packaging. The high‑thermal‑conductivity copper‑clad ceramic plates developed by Curmilk (Germany) are made by sintering ceramic substrates (AlN or Al₂O₃) and conductive layers (Cu) at high temperature and high pressure without adhesives, thus offering good thermal conductivity, high strength, and strong insulation. Among them, AlN has a thermal conductivity of 160 W/(m·K) and a coefficient of thermal expansion of 4.0×10⁻⁶/°C (comparable to silicon’s 3.2×10⁻⁶/°C), thereby reducing packaging thermal stress.

During LED operation, photons generated by radiative recombination suffer losses when emitted outward, mainly from three aspects: absorption by internal structural defects and materials in the chip; reflection loss at the exit interface due to refractive index mismatch; and total internal reflection loss when the incident angle exceeds the critical angle. Therefore, many photons cannot escape from the chip to the outside. By coating the chip surface with a transparent adhesive layer (encapsulant) with a relatively high refractive index, which is located between the chip and air, the loss of photons at the interface is effectively reduced and the light extraction efficiency is improved. In addition, the encapsulant also provides mechanical protection, stress relief, and serves as a light guide structure. Thus, it is required to have high transmittance, high refractive index, good thermal stability, good fluidity, and ease of dispensing. To improve the reliability of LED packaging, the encapsulant should also have low moisture absorption, low stress, and aging resistance. Currently, commonly used encapsulants include epoxy resin and silicone. Silicone is superior to epoxy resin in terms of high transmittance, high refractive index, good thermal stability, low stress, and low moisture absorption, and is widely used in high‑power LED packaging, though at higher cost. Studies show that increasing the refractive index of silicone can effectively reduce photon loss caused by the refractive index barrier and improve external quantum efficiency, but silicone properties are significantly affected by ambient temperature. As temperature increases, the internal thermal stress in the silicone rises, leading to a decrease in its refractive index, which in turn affects the LED’s luminous efficacy and light intensity distribution.

The function of phosphors is to perform color conversion to generate white light. Their key characteristics include particle size, shape, luminous efficiency, conversion efficiency, and stability (thermal and chemical), among which luminous efficiency and conversion efficiency are crucial. Studies indicate that as temperature rises, the quantum efficiency of phosphors decreases, light output diminishes, and the emission wavelength may shift, causing changes in the color temperature and chromaticity of white LEDs. Higher temperatures also accelerate phosphor aging. This is because the phosphor coating, made by mixing phosphor powder with epoxy or silicone, has poor heat dissipation; when exposed to violet or ultraviolet light, it is prone to thermal quenching and aging, reducing luminous efficiency. In addition, the thermal stability of the encapsulant and phosphors at high temperatures is also problematic. Since commonly used phosphor particles are larger than 1 μm in size and have a refractive index of ≥1.85, while silicone typically has a refractive index of about 1.5, the mismatch in refractive index and the particle size far exceeding the light‑scattering limit (30 nm) cause light scattering at the phosphor particle surface, reducing light extraction efficiency. By incorporating nano‑sized phosphors into silicone, the refractive index can be increased to above 1.8, reducing light scattering and improving LED light extraction efficiency by 10%–20%, while also improving color quality.

The traditional phosphor coating method involves mixing phosphors with the encapsulant and then dispensing the mixture onto the chip. Because the coating thickness and shape cannot be precisely controlled, the emitted light exhibits color inconsistency, appearing bluish or yellowish. Lumileds’ conformal coating technology enables uniform phosphor coating, ensuring color uniformity. However, studies show that when phosphors are coated directly on the chip surface, light extraction efficiency is low due to light scattering. To address this, Rensselaer Polytechnic Institute proposed a Scattered Photon Extraction (SPE) method, in which a focusing lens is placed on the chip surface and a phosphor‑containing glass plate is positioned at a certain distance from the chip. This not only improves device reliability but also greatly enhances light extraction efficiency (by 60%).

**(2) Optical Design**

1. **Leaded (Lamp) LED Packaging**  

   Leaded packaging is the commonly used φ3–5 mm package structure. It is generally used for LEDs with low current (20–30 mA) and low power (less than 0.1 W), mainly for instrument displays or indicators, and can also be used as display screens in large‑scale integration. Its disadvantages are relatively high thermal resistance (generally above 100 K/W) and short lifetime.

2. **Surface‑Mount (SMT) LED Packaging**  

   Surface‑mount technology (SMT) is a packaging technology that allows packaged devices to be directly mounted and soldered onto designated locations on a PCB surface. Specifically, using specific tools or equipment, the device leads are aligned with the pad patterns pre‑coated with adhesive and solder paste, and then directly mounted onto the PCB surface without drilled mounting holes. After wave soldering or reflow soldering, reliable mechanical and electrical connections are established between the device and the circuit. SMT offers advantages such as high reliability, good high‑frequency characteristics, and ease of automation, making it one of the most popular packaging technologies and processes in the electronics industry.

3. **Chip‑On‑Board (COB) LED Packaging**  

   Zhongshan Guzhen Zhengtai Optoelectronics Technology Co., Ltd.  

   www.dengjunhui-led.com

   COB (Chip On Board) is a packaging technology in which LED chips are directly attached to a PCB using adhesives or solder, and electrical interconnection between the chip and the PCB is achieved through wire bonding. The PCB can be low‑cost FR‑4 material (glass‑fiber‑reinforced epoxy) or high‑thermal‑conductivity metal‑based or ceramic‑based composite materials (e.g., aluminum‑based boards or copper‑clad ceramic substrates). Wire bonding can be performed using high‑temperature thermosonic bonding (gold ball bonding) or room‑temperature ultrasonic bonding (aluminum wedge bonding). COB technology is mainly used for high‑power multi‑chip array LED packaging. Compared with SMT, it not only significantly increases packaging power density but also reduces packaging thermal resistance (typically 6–12 W/(m·K)).

4. **System‑in‑Package (SiP) LED Packaging**  

   SiP (System in Package) is a new packaging integration approach developed in recent years to meet the requirements of portable devices and system miniaturization, based on System‑on‑Chip (SOC) technology. For SiP‑LED, not only can multiple light‑emitting chips be assembled in one package, but various types of devices (such as power supplies, control circuits, optical microstructures, sensors, etc.) can also be integrated to build a more complex, complete system. Compared with other packaging structures, SiP offers advantages such as good process compatibility (using existing electronic packaging materials and processes), high integration, low cost, the ability to provide new functions, ease of modular testing, and short development cycles. According to technology type, SiP can be divided into four categories: chip‑stacking type, module type, MCM type, and 3D packaging type.

At present, for high‑brightness LED devices to replace incandescent lamps and high‑pressure mercury lamps, the total luminous flux must be increased. This can be achieved by increasing integration density, raising current density, and using larger‑size chips. However, all these measures increase the power density of LEDs; if heat dissipation is inadequate, the LED chip junction temperature will rise, directly affecting device performance (e.g., reduced luminous efficiency, red shift of emitted light, and shorter lifetime). Multi‑chip array packaging is currently one of the most feasible solutions for obtaining high luminous flux, but the density of LED array packaging is limited by cost, available space, electrical connections, and especially heat dissipation. Due to the high integration of light‑emitting chips, the temperature on the heat‑dissipating substrate is very high, so effective heat sink structures and suitable packaging processes must be used. Common heat sink structures are divided into passive and active cooling. Passive cooling generally uses fins with high fin coefficients to dissipate heat to the environment through natural convection between the fins and air. This solution is simple in structure and highly reliable, but because the natural convection heat transfer coefficient is low, it is only suitable for low power density and low integration. For high‑power LED packaging, active cooling must be employed, such as fins with fans, heat pipes, forced liquid convection, microchannel cooling, and phase‑change cooling.

In terms of system integration, Taiwan’s NeoNeon Optoelectronics used SiP technology combined with fin‑and‑heat‑pipe high‑performance cooling modules to develop 72 W and 80 W high‑brightness white LED light sources. With a low packaging thermal resistance (4.38 °C/W), at an ambient temperature of 25 °C, the LED junction temperature was controlled below 60 °C, ensuring long lifetime and good luminous performance. Huazhong University of Science and Technology, using COB packaging and micro‑jet active cooling technology, has packaged ultra‑high‑power 220 W and 1500 W white LED light sources.

**(3) Packaging Structure and Processes**

**(4) Large‑Scale Packaging Manufacturing Technology**

Wafer bonding technology means that the fabrication of chip structures and circuits as well as packaging are all performed on the wafer, and after packaging is completed, the wafer is diced to form individual chips. In contrast, die bonding means that after chip structures and circuits are fabricated on the wafer, the wafer is diced into individual dies, which are then packaged individually (similar to the current LED packaging process), as shown in Figure 6. Clearly, wafer‑level packaging is more efficient and of higher quality. Since packaging cost accounts for a large proportion of the total manufacturing cost of LED devices, changing the existing LED packaging form (from die bonding to wafer bonding) can greatly reduce packaging costs. In addition, wafer‑level packaging can improve the cleanliness of LED device production, prevent damage to device structures caused by dicing and sorting before bonding, and improve packaging yield and reliability, making it an effective means of reducing packaging costs.

Moreover, for high‑power LED packaging, during chip design and packaging design, it is necessary to adopt packaging forms with as few process steps as possible (package‑less packaging), while simplifying the packaging structure and minimizing the number of thermal and optical interfaces to reduce packaging thermal resistance and improve light extraction efficiency.

**(5) Packaging Reliability Testing and Evaluation**

Failure modes of LED devices mainly include electrical failures (e.g., short circuits or open circuits), optical failures (e.g., yellowing of the encapsulant due to high temperature, degradation of optical performance), and mechanical failures (e.g., wire breakage, solder joint failure), all of which are related to the packaging structure and process. The service life of LEDs is defined by the mean time to failure (MTTF). For lighting applications, it generally refers to the time when the output luminous flux decays to 70% of its initial value (for display applications, it is usually defined as 50% of the initial value). Because LEDs have a long lifetime, accelerated environmental testing is usually employed for reliability testing and assessment. Test contents mainly include high‑temperature storage (100 °C, 1000 h), low‑temperature storage (−55 °C, 1000 h), high‑temperature/high‑humidity (85 °C/85%, 1000 h), temperature cycling (85 °C to −55 °C), thermal shock, corrosion resistance, solvent resistance, mechanical shock, etc. However, accelerated environmental testing is only one aspect; the study of mechanisms and methods for predicting LED lifetime remains a challenging issue.

**III. Development Trends of High‑Power LEDs**

Compared with traditional lighting fixtures, LED lamps do not require filters or color filters to produce colored light; they are not only highly efficient and have pure color, but can also achieve dynamic or gradual color changes. While changing color temperature, they maintain a high color rendering index to meet different application needs. However, this also places new demands on packaging, specifically:

**(1) Modularization**  

By interconnecting multiple LED lamps (or modules), good luminous flux addition can be achieved to meet high‑brightness lighting requirements. Modular technology allows multiple point light sources or LED modules to be combined in arbitrary shapes to satisfy lighting needs in different fields.

**(2) Maximization of System Efficiency**  

To improve the light extraction efficiency of LED lamps, in addition to appropriate LED drivers, efficient heat dissipation structures and processes must be adopted, and internal/external optical designs must be optimized to enhance overall system efficiency.

**(3) Low Cost**  

For LED lamps to penetrate the market, they must be cost‑competitive (mainly in terms of initial installation cost). Packaging accounts for a large portion of the total manufacturing cost of LED lamps. Therefore, adopting new packaging structures and technologies to improve the cost‑performance ratio (luminous efficacy per unit cost) is the key to commercializing LED lamps.

**(4) Easy Replacement and Maintenance**  

Because LED light sources have long lifetimes and low maintenance costs, high reliability of LED lamp packaging is required. LED lamp designs should be easy to improve to accommodate future, more efficient LED chip packaging requirements, and the interchangeability of LED chips should be good so that lamp manufacturers can choose which chips to use.

LED lamps can be composed of multiple distributed point light sources. Because the chips are small, the packaged lamps are lightweight, compact, and can meet various shape and integration requirements. The only drawback is the lack of established design standards, but this also provides ample creative freedom for designers. In addition, the primary goal of LED lighting control is power supply. Since the general utility power is high‑voltage AC (220 V, AC), while LEDs require constant‑current or current‑limited power supplies, conversion circuits or embedded control circuits (ASICs) must be used to achieve advanced calibration and closed‑loop feedback control systems. Furthermore, through digital lighting control technology, the use and control of solid‑state light sources rely mainly on intelligent control and management software, establishing new connections among users, information, and light sources, while fully exploiting the imagination of designers and consumers.

**IV. Concluding Remarks**

LED packaging is a research topic involving multiple disciplines (such as optics, thermal science, mechanics, electrical engineering, mechanics, materials science, and semiconductors). From a certain perspective, LED packaging is not only a manufacturing technology but also a fundamental science, requiring an understanding and application of the physical principles of thermal, optical, material, and mechanical behaviors. Packaging design should be carried out simultaneously with chip design, and optical, thermal, electrical, and structural performance must be considered in an integrated manner. In the packaging process, although material selection (heat‑dissipating substrates, phosphors, encapsulants) is important, the packaging structure (such as thermal interfaces and optical interfaces) also significantly affects LED efficiency and reliability. High‑power white LED packaging must adopt new materials, new processes, and new concepts. For LED lamps in particular, the light source, heat dissipation, power supply, and luminaire must be integrated into a holistic design.



Author: Guangdong DONESON New Materials Co., Ltd.
0
High power LED conductive silver paste and its packaging technology and trends
Long by picture save/share

更多资讯


Copyright ©  Guangdong DONESON New Materials Co., Ltd


Contact Us

Phone: 0760-86511168

Phone: 18825004900 (Liu Gong, same WeChat account)

Phone: 18923325516 (Janny Huang from the Ministry of Foreign Trade, same WeChat number)

Fax: 0760-86511171

Address: No. 7 Zhichuang Road, Banfu Town, Zhongshan City


Scan to follow





Contact Us

Phone: 0760-86511168

Phone: 18825004900 (Liu Gong, same WeChat account)

Phone: 18923325516 (Janny Huang from the Ministry of Foreign Trade, same WeChat number)

Fax: 0760-86511171

Address: No. 7 Zhichuang Road, Banfu Town, Zhongshan City


Scan to follow

  


Copyright ©  Guangdong DONESON New Materials Co., Ltd

Add WeChat friend to learn more about the product
Use Enterprise WeChat
"Scan" to join the group chat
Copy success!
Add WeChat friend to learn more about the product
I see.