2012-05-19 00:00:00
Click:
**High-end LED Encapsulation Compounds: Why Must ETBN Epoxy Toughener Be Used?**
The high-end LED encapsulation compound market has long been dominated by foreign suppliers—until domestic players came to realize that producing this material requires a core ingredient: ETBN, an epoxy resin toughener that was not previously manufactured in China. Given the special corrosion resistance, sealing performance, and other property requirements, high-end LED encapsulation compounds are generally based on epoxy resins. With so many types of epoxy tougheners available, why must the expensive ETBN be used?
**First, substrate compatibility requirements:** LED encapsulation imposes very strict corrosion-resistance standards on adhesives, especially for large enterprises, which require that adhesive products be chlorine-free to minimize substrate corrosion. At the same time, the substrate must not compromise the toughener's performance; adhesives whose toughening effect is easily affected by the substrate cannot meet LED encapsulation needs. Currently, the only epoxy toughener that satisfies both conditions—neither corroding the substrate nor being affected by it—is essentially reactive liquid nitrile rubber.
**Second, special environmental requirements:** Large LED encapsulation companies have rigorous environmental standards, demanding that adhesives be non-toxic and harmless. This requirement applies not only to the product itself but also extends to its subsequent use and decomposition. Polyurethane and certain polyether-based products fail to meet this criterion.
**Third, unique performance requirements for use:** LED products require that the encapsulation compound can be easily removed and re-applied for maintenance or rework.
1. Unlike typical applications, LED products demand extremely tight sealing after encapsulation, along with good adhesion to the substrate.
2. At the same time, the compound must be easy to clean off, which calls for an ideal glass transition temperature. The cleanup process should have minimal environmental impact.
3. The compound must cure normally at room temperature during encapsulation. This single requirement rules out most tougheners that rely on high-temperature anhydride curing.
Domestic manufacturers only became aware of the importance of ETBN in LED encapsulation after 2009. Before that, without CHX100-type ETBN, domestic LED encapsulation compounds either relied on in-house modified CTBN or were only supplied to low-end workshops. That was the reality.
Now, you can use CHX100-type ETBN—a high-end epoxy toughener whose main component is 100% epoxy-terminated reactive liquid nitrile rubber. It delivers first-class toughening for your epoxy adhesives while meeting the following special requirements:
A. Does not corrode substrates, nor is the toughening effect compromised by substrates. Contains no chlorine, halogens, or phosphorus.
B. Achieves outstanding toughening in room-temperature curing systems.
C. Provides excellent encapsulation performance during use, and allows easy cleanup during disassembly and repair.
D. Inherently environmentally friendly; its combustion and decomposition byproducts are also environmentally benign.
LED products are generally encapsulated with epoxy adhesives—that's straightforward. However, meeting the following requirements is challenging. Can your product satisfy them?
1. Adhesive strength at room temperature (on different substrates) ≥ 15 MPa; at -50°C to 55°C, ≥ 12 MPa.
2. Successively withstand the following conditions:
- Continuous 168 hours at -50°C,
- Continuous 168 hours at 55°C,
- Room temperature at 98% relative humidity for 168 hours,
- 55°C at 20% relative humidity for 168 hours.
After these four steps, in addition to meeting adhesive and shear strength requirements, the following must be achieved:
- 2-1 No fine cracks of any kind.
- 2-2 Volume change of the encapsulant throughout the entire process ≤ 0.05%.
3. To avoid adverse effects on LED products and to facilitate operations and production, the LED encapsulant must cure at room temperature. No bubbles are allowed during application to ensure encapsulation quality.
4. The adhesive must not contain halogens (especially chlorine) to avoid material corrosion. At the same time, various substrates must not adversely affect the adhesive.
5. Considering that LED products may require maintenance and re-encapsulation, unlike many other adhesives, this LED encapsulant actually requires a relatively low heat deflection temperature, with a glass transition temperature typically specified at 65°C–70°C.
6. The adhesive must first and foremost be safe and non-toxic. It must not volatilize any environmentally harmful substances during use, nor during decomposition (or combustion) after disposal.
7. Environmentally friendly: The product must fully comply with environmental requirements, and when disposed of as waste, its environmental impact must be minimized (subject to professional testing at that time).
There are many LED encapsulant manufacturers in China, but very few can meet all the above requirements. To achieve these targets, ETBN must be used as the toughener (the same choice as Henkel Loctite)—a raw material previously unavailable domestically. A very small number of domestic companies partially meet the requirements by pre-polymerizing CTBN in-house, but because CTBN pre-polymerization and application are highly inconsistent, product quality is unstable.
Now, with CHX100-type ETBN—provided that your other raw materials are equally excellent and your formulation is scientifically sound—you too can produce world-class LED encapsulation compounds!
更多资讯